View TDA8510_119066.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

INTEGRATED CIRCUITS
DATA SHEET
TDA8510J 26 W BTL and 2 x 13 W SE power amplifiers
Preliminary specification Supersedes data of 1999 Jun 14 File under Integrated Circuits, IC01 1999 Dec 14
Philips Semiconductors
Preliminary specification
26 W BTL and 2 x 13 W SE power amplifiers
FEATURES * Requires very few external components * High output power * Low output offset voltage (BTL channel) * Fixed gain * Diagnostic facility (distortion, short-circuit and temperature detection) * Good ripple rejection * Mode select switch (operating, mute and standby) * AC and DC short-circuit safe to ground and to VP * Low power dissipation in any short-circuit condition * Thermally protected * Reverse polarity safe QUICK REFERENCE DATA SYMBOL General VP IORM Iq(tot) Istb BTL channel Po SVRR Vn(o) Zi VOO Po output power supply voltage ripple rejection noise output voltage input impedance DC output offset voltage Rs = 0 RL = 4 ; THD = 10% - 46 - 25 - THD = 10% RL = 4 RL = 2 SVRR Vn(o) Zi supply voltage ripple rejection noise output voltage input impedance Rs = 0 - - 46 - 50 7 13 - 50 - - - - - - 26 - 70 - - - - - - supply voltage repetitive peak output current total quiescent current standby current 6 - - - 15 - 80 0.1 PARAMETER CONDITIONS MIN. TYP. * Electrostatic discharge protection * No switch-on/switch-off plop * Flexible leads * Low thermal resistance
TDA8510J
* Identical inputs (inverting and non-inverting). GENERAL DESCRIPTION The TDA8510J is an integrated class-B output amplifier in a 17-lead single-in-line (SIL) power package. It contains a 26 W Bridge-Tied Load (BTL) amplifier and 2 x 13 W Single-Ended (SE) amplifiers. The device is primarily developed for multi-media applications and active speaker systems (stereo with subwoofer).
MAX.
UNIT
18 4 - 100
V A mA A W dB V k mV
150
Single-ended channels output power W W dB V k
ORDERING INFORMATION TYPE NUMBER TDA8510J PACKAGE NAME DESCRIPTION VERSION SOT243-1
DBS17P plastic DIL-bent-SIL power package; 17 leads (lead length 12 mm)
1999 Dec 14
2
Philips Semiconductors
Preliminary specification
26 W BTL and 2 x 13 W SE power amplifiers
BLOCK DIAGRAM
TDA8510J
VP1 5 non-inverting input 1 1 60 k VA 2 k 18 k non-inverting input 2 3 60 k VA 2 k 18 k VP power stage mute switch Cm power stage mute switch Cm
VP2 13
TDA8510J
6 output 1
8
output 2
14 standby switch VA PROTECTIONS thermal short-circuit standby reference voltage mute switch 16 15 k
mode select switch
15 k x1 supply voltage ripple rejection 4
diagnostic output
mute reference voltage Cm
mute switch 60 k inverting input 3 15 VA 2 k 18 k non-inverting input 4 17 60 k VA 2 k input reference voltage 2 18 k 9 mute switch
10
output 3
power stage
Cm
12
output 4
power stage
7 GND1
11 GND2 power ground (substrate)
MGL428
ground (signal)
not connected
Fig.1 Block diagram.
1999 Dec 14
3
Philips Semiconductors
Preliminary specification
26 W BTL and 2 x 13 W SE power amplifiers
PINNING SYMBOL -INV1 SGND -INV2 RR VP1 OUT1 GND1 OUT2 n.c. OUT3 GND2 OUT4 VP2 MODE INV3 VDIAG -INV4 PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 DESCRIPTION non-inverting input 1 signal ground non-inverting input 2 supply voltage ripple rejection supply voltage 1 output 1 power ground 1 output 2 not connected output 3 power ground 2 output 4 supply voltage 2 mode select switch input inverting input 3 diagnostic output non-inverting input 4
VP2 13 MODE 14 INV3 15 VDIAG 16 -INV4 17 -INV1 SGND -INV2 RR VP1 OUT1 GND1 OUT2 n.c. 1 2 3 4 5 6 7 8 9 TDA8510J
TDA8510J
OUT3 10 GND2 11 OUT4 12
MGL427
Fig.2 Pin configuration.
1999 Dec 14
4
Philips Semiconductors
Preliminary specification
26 W BTL and 2 x 13 W SE power amplifiers
FUNCTIONAL DESCRIPTION The TDA8510J contains four identical amplifiers and can be used for two Single-Ended (SE) channels (fixed gain 20 dB) and one Bridge-Tied Load (BTL) channel (fixed gain 26 dB). Special features of the device are: Mode select switch (pin 14) * Low standby current (<100 A) * Low switching current (low cost supply switch) * Mute facility. To avoid switch-on plops, it is advised to keep the amplifier in the mute mode during 100 ms (charging of the input capacitors at pins 1, 3, 15 and 17). This can be achieved by: * Microcontroller control * External timing circuit (see Fig.8). Diagnostic output (pin 16) DYNAMIC DISTORTION DETECTOR (DDD) At the onset of clipping of one or more output stages, the dynamic distortion detector becomes active and pin 16 goes LOW. This information can be used to drive a sound processor or DC volume control to attenuate the input signal and thus limit the distortion. The output level of pin 16 is independent of the number of channels that are clipping (see Figs 3 and 4). SHORT-CIRCUIT PROTECTION When a short-circuit occurs at one or more outputs to ground or to the supply voltage, the output stages are switched off until the short-circuit is removed and the device is switched on again, with a delay of approximately 20 ms, after removal of the short-circuit. During this short-circuit condition, pin 16 is continuously LOW. When a short-circuit across the load of one or more channels occurs the output stages are switched off for approximately 20 ms. After that time it is checked during approximately 50 s to see whether the short-circuit is still present. Due to this duty cycle of 50 s/20 ms the average current consumption during this short-circuit condition is very low (approximately 40 mA).
handbook, halfpage VO
TDA8510J
During this short-circuit condition, pin 16 is LOW for 20 ms and HIGH for 50 s (see Fig.5). The power dissipation in any short-circuit condition is very low.
MGA705
0
V16 VP 0 t
Fig.3 Distortion detector waveform; BTL channel.
handbook, halfpage VO
MGA706
0
V16 VP 0 t
Fig.4 Distortion detector waveform; SE channels.
1999 Dec 14
5
Philips Semiconductors
Preliminary specification
26 W BTL and 2 x 13 W SE power amplifiers
TDA8510J
handbook, full pagewidthcurrent
in output stage
MGL214
V16 VP
short-circuit over the load 20 ms
t
t 50 s
Fig.5 Short-circuit waveform.
TEMPERATURE DETECTION When the virtual junction temperature Tvj reaches 150 C, pin 16 will be active LOW. OPEN-COLLECTOR OUTPUT Pin 16 is an open-collector output, which allows pin 16 of more devices being tied together. LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 134). SYMBOL VP IOSM IORM Vsc Vrp Ptot Tstg Tamb Tvj PARAMETER supply voltage non-repetitive peak output current repetitive peak output current AC and DC short-circuit safe voltage reverse polarity voltage total power dissipation storage temperature operating ambient temperature virtual junction temperature CONDITIONS operating no signal - - - - - - - -55 -40 - MIN. 18 20 6 4 18 6 60 +150 +85 150 MAX. V V A A V V W C C C UNIT
THERMAL CHARACTERISTICS In accordance with IEC 747-1. SYMBOL Rth(j-a) Rth(j-c) 1999 Dec 14 PARAMETER thermal resistance from junction to ambient thermal resistance from junction to case (see Fig.6) 6 CONDITIONS in free air VALUE 40 1.3 UNIT K/W K/W
Philips Semiconductors
Preliminary specification
26 W BTL and 2 x 13 W SE power amplifiers
TDA8510J
handbook, halfpage
virtual junction output 2 output 3 output 4
output 1
3.0 K/W
3.0 K/W 3.0 K/W
3.0 K/W
0.7 K/W
0.7 K/W
MEA860 - 2
0.2 K/W
case
Fig.6 Equivalent thermal resistance network.
1999 Dec 14
7
Philips Semiconductors
Preliminary specification
26 W BTL and 2 x 13 W SE power amplifiers
DC CHARACTERISTICS VP = 15 V; Tamb = 25 C; measured in Fig.7; unless otherwise specified. SYMBOL Supply VP Iq(tot) VO VOO VSW(on) MUTE CONDITION Vmute VO VOO Vstb Istb Isw(on) VDIAG Notes 1. The circuit is DC adjusted at VP = 6 to 18 V and AC operating at VP = 8.5 to 18 V. 2. Only for BTL channel (V12-10). mute voltage output voltage in mute position DC output offset voltage VI(max) = 1 V; f = 1 kHz note 2 3.3 - - 0 - - any short-circuit or clipping - - - - - - 12 - supply voltage total quiescent current DC output voltage DC output offset voltage note 2 note 1 6 - - - 8.5 15 80 6.9 - - PARAMETER CONDITIONS MIN. TYP.
TDA8510J
MAX.
UNIT
18 160 - 150 - 6.4 2 150
V mA V mV
Mode select switch switch-on voltage level V
V mV mV
STANDBY CONDITION standby voltage standby current switch-on current 2 100 40 V A A V
Diagnostic output (pin 16) diagnostic output voltage 0.6
1999 Dec 14
8
Philips Semiconductors
Preliminary specification
26 W BTL and 2 x 13 W SE power amplifiers
AC CHARACTERISTICS VP = 15 V; f = 1 kHz; Tamb = 25 C; measure in Fig.7; unless otherwise specified. SYMBOL BTL channel Po output power note 1 THD = 0.5% THD = 10% THD B fro(l) fro(h) Gv SVRR total harmonic distortion power bandwidth low frequency roll-off high frequency roll-off closed loop voltage gain supply voltage ripple rejection note 3 on mute standby Zi Vn(o) input impedance noise output voltage on; Rs = 0 ; note 4 on; Rs = 10 k; note 4 mute; notes 4 and 5 cs THD channel separation Rs = 10 k V16 0.6 V; no short-circuit DYNAMIC DISTORTION DETECTOR total harmonic distortion - 10 48 46 80 25 - - - 40 - - - 30 70 100 60 60 Po = 1 W THD = 0.5%; Po = -1 dB; with respect to 16 W at -1 dB; note 2 at -1 dB - 20 25 16 22 - - 20 26 0.06 20 to 15000 25 - 26 PARAMETER CONDITIONS MIN. TYP.
TDA8510J
MAX.
UNIT
- - - - - - 27 - - - 38 - 200 - - -
W W % Hz Hz kHz dB dB dB dB k V V V dB
%
1999 Dec 14
9
Philips Semiconductors
Preliminary specification
26 W BTL and 2 x 13 W SE power amplifiers
SYMBOL PARAMETER CONDITIONS MIN. TYP.
TDA8510J
MAX.
UNIT
Single-ended channels Po output power note 1 THD = 0.5% THD = 10% RL1 = 4 ; note 1 THD = 0.5% THD = 10% THD fro(l) fro(h) Gv SVRR total harmonic distortion low frequency roll-off high frequency roll-off closed loop voltage gain supply voltage ripple rejection note 3 on mute standby Zi Vn(o) input impedance noise output voltage on; Rs = 0 ; note 4 on; Rs = 10 k; note 4 mute; notes 4 and 5 cs Gv THD Notes 1. Output power is measured directly at the output pins of the IC. 2. Frequency response externally fixed. 3. Ripple rejection measured at the output with a source impedance of 0 , maximum ripple amplitude of 2 V (p-p) and at a frequency of between 100 Hz and 10 kHz. 4. Noise measured in a bandwidth of 20 Hz to 20 kHz. 5. Noise output voltage independent of Rs (Vi = 0 V). channel separation channel unbalance V16 0.6 V; no short-circuit Rs = 10 k 48 46 80 50 - - - 40 - - - - - 60 50 70 50 60 - 10 - - - 75 - 100 - - 1 - dB dB dB k V V V dB dB Po = 1 W at -1 dB; note 2 at -1 dB - - - - 20 19 5.5 7 0.06 25 - 20 - - - - - 21 W W % Hz kHz dB 8 11 10 13 - - W W
DYNAMIC DISTORTION DETECTOR total harmonic distortion %
1999 Dec 14
10
Philips Semiconductors
Preliminary specification
26 W BTL and 2 x 13 W SE power amplifiers
TEST AND APPLICATION INFORMATION
TDA8510J
handbook, full pagewidth
mode switch
10 k 16 5 13
100 nF
VP 2200 F
14
220 nF input 1
TDA8510J
1 + - 60 k - 6 1000 F RL1 2 8 1000 F RL1 2
220 nF input 2 ground (signal)
3 2 60 k 4
+
reference voltage 60 k - + 9
supply voltage ripple rejection
100 1/2VP F 15
not connected
10
inputs 3 and 4
470 nF
60 k - 17 + 12
RL2 4
7
11
MGL429
power ground (substrate)
Fig.7 Application diagram.
1999 Dec 14
11
Philips Semiconductors
Preliminary specification
26 W BTL and 2 x 13 W SE power amplifiers
Mode select switch To avoid switch-on plops, it is advised to keep the amplifier in the mute mode during >100 ms (charging of the input capacitors at pins 1, 3, 15 and 17. The circuit in Fig.8 slowly ramps up the voltage at the mode select switch pin when switching on and results in fast muting when switching off.
TDA8510J
handbook, halfpage
VP
10 k
100
47 F
mode select switch 100 k
MGA708
Fig.8 Mode select switch circuitry.
1999 Dec 14
12
Philips Semiconductors
Preliminary specification
26 W BTL and 2 x 13 W SE power amplifiers
PACKAGE OUTLINE DBS17P: plastic DIL-bent-SIL power package; 17 leads (lead length 12 mm)
TDA8510J
SOT243-1
non-concave D x Dh
Eh
view B: mounting base side
d
A2
B j E A
L3
L
Q c vM
1 Z e e1 bp wM
17 m e2
0
5 scale
10 mm
DIMENSIONS (mm are the original dimensions) UNIT mm A 17.0 15.5 A2 4.6 4.2 bp 0.75 0.60 c 0.48 0.38 D (1) 24.0 23.6 d 20.0 19.6 Dh 10 E (1) 12.2 11.8 e 2.54 e1 e2 Eh 6 j 3.4 3.1 L 12.4 11.0 L3 2.4 1.6 m 4.3 Q 2.1 1.8 v 0.8 w 0.4 x 0.03 Z (1) 2.00 1.45
1.27 5.08
Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT243-1 REFERENCES IEC JEDEC EIAJ EUROPEAN PROJECTION
ISSUE DATE 95-03-11 97-12-16
1999 Dec 14
13
Philips Semiconductors
Preliminary specification
26 W BTL and 2 x 13 W SE power amplifiers
SOLDERING Introduction to soldering through-hole mount packages This text gives a brief insight to wave, dip and manual soldering. A more in-depth account of soldering ICs can be found in our "Data Handbook IC26; Integrated Circuit Packages" (document order number 9398 652 90011). Wave soldering is the preferred method for mounting of through-hole mount IC packages on a printed-circuit board. Soldering by dipping or by solder wave The maximum permissible temperature of the solder is 260 C; solder at this temperature must not be in contact with the joints for more than 5 seconds.
TDA8510J
The total contact time of successive solder waves must not exceed 5 seconds. The device may be mounted up to the seating plane, but the temperature of the plastic body must not exceed the specified maximum storage temperature (Tstg(max)). If the printed-circuit board has been pre-heated, forced cooling may be necessary immediately after soldering to keep the temperature within the permissible limit. Manual soldering Apply the soldering iron (24 V or less) to the lead(s) of the package, either below the seating plane or not more than 2 mm above it. If the temperature of the soldering iron bit is less than 300 C it may remain in contact for up to 10 seconds. If the bit temperature is between 300 and 400 C, contact may be up to 5 seconds.
Suitability of through-hole mount IC packages for dipping and wave soldering methods SOLDERING METHOD PACKAGE DIPPING DBS, DIP, HDIP, SDIP, SIL Note 1. For SDIP packages, the longitudinal axis must be parallel to the transport direction of the printed-circuit board. DEFINITIONS Data sheet status Objective specification Preliminary specification Product specification Limiting values Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. This data sheet contains target or goal specifications for product development. This data sheet contains preliminary data; supplementary data may be published later. This data sheet contains final product specifications. suitable suitable(1) WAVE
1999 Dec 14
14
Philips Semiconductors
Preliminary specification
26 W BTL and 2 x 13 W SE power amplifiers
NOTES
TDA8510J
1999 Dec 14
15
Philips Semiconductors - a worldwide company
Argentina: see South America Australia: 3 Figtree Drive, HOMEBUSH, NSW 2140, Tel. +61 2 9704 8141, Fax. +61 2 9704 8139 Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. +43 1 60 101 1248, Fax. +43 1 60 101 1210 Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6, 220050 MINSK, Tel. +375 172 20 0733, Fax. +375 172 20 0773 Belgium: see The Netherlands Brazil: see South America Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor, 51 James Bourchier Blvd., 1407 SOFIA, Tel. +359 2 68 9211, Fax. +359 2 68 9102 Canada: PHILIPS SEMICONDUCTORS/COMPONENTS, Tel. +1 800 234 7381, Fax. +1 800 943 0087 China/Hong Kong: 501 Hong Kong Industrial Technology Centre, 72 Tat Chee Avenue, Kowloon Tong, HONG KONG, Tel. +852 2319 7888, Fax. +852 2319 7700 Colombia: see South America Czech Republic: see Austria Denmark: Sydhavnsgade 23, 1780 COPENHAGEN V, Tel. +45 33 29 3333, Fax. +45 33 29 3905 Finland: Sinikalliontie 3, FIN-02630 ESPOO, Tel. +358 9 615 800, Fax. +358 9 6158 0920 France: 51 Rue Carnot, BP317, 92156 SURESNES Cedex, Tel. +33 1 4099 6161, Fax. +33 1 4099 6427 Germany: Hammerbrookstrae 69, D-20097 HAMBURG, Tel. +49 40 2353 60, Fax. +49 40 2353 6300 Hungary: see Austria India: Philips INDIA Ltd, Band Box Building, 2nd floor, 254-D, Dr. Annie Besant Road, Worli, MUMBAI 400 025, Tel. +91 22 493 8541, Fax. +91 22 493 0966 Indonesia: PT Philips Development Corporation, Semiconductors Division, Gedung Philips, Jl. Buncit Raya Kav.99-100, JAKARTA 12510, Tel. +62 21 794 0040 ext. 2501, Fax. +62 21 794 0080 Ireland: Newstead, Clonskeagh, DUBLIN 14, Tel. +353 1 7640 000, Fax. +353 1 7640 200 Israel: RAPAC Electronics, 7 Kehilat Saloniki St, PO Box 18053, TEL AVIV 61180, Tel. +972 3 645 0444, Fax. +972 3 649 1007 Italy: PHILIPS SEMICONDUCTORS, Via Casati, 23 - 20052 MONZA (MI), Tel. +39 039 203 6838, Fax +39 039 203 6800 Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108-8507, Tel. +81 3 3740 5130, Fax. +81 3 3740 5057 Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL, Tel. +82 2 709 1412, Fax. +82 2 709 1415 Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR, Tel. +60 3 750 5214, Fax. +60 3 757 4880 Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905, Tel. +9-5 800 234 7381, Fax +9-5 800 943 0087 Middle East: see Italy Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB, Tel. +31 40 27 82785, Fax. +31 40 27 88399 New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND, Tel. +64 9 849 4160, Fax. +64 9 849 7811 Norway: Box 1, Manglerud 0612, OSLO, Tel. +47 22 74 8000, Fax. +47 22 74 8341 Pakistan: see Singapore Philippines: Philips Semiconductors Philippines Inc., 106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI, Metro MANILA, Tel. +63 2 816 6380, Fax. +63 2 817 3474 Poland: Al.Jerozolimskie 195 B, 02-222 WARSAW, Tel. +48 22 5710 000, Fax. +48 22 5710 001 Portugal: see Spain Romania: see Italy Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW, Tel. +7 095 755 6918, Fax. +7 095 755 6919 Singapore: Lorong 1, Toa Payoh, SINGAPORE 319762, Tel. +65 350 2538, Fax. +65 251 6500 Slovakia: see Austria Slovenia: see Italy South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale, 2092 JOHANNESBURG, P.O. Box 58088 Newville 2114, Tel. +27 11 471 5401, Fax. +27 11 471 5398 South America: Al. Vicente Pinzon, 173, 6th floor, 04547-130 SAO PAULO, SP, Brazil, Tel. +55 11 821 2333, Fax. +55 11 821 2382 Spain: Balmes 22, 08007 BARCELONA, Tel. +34 93 301 6312, Fax. +34 93 301 4107 Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM, Tel. +46 8 5985 2000, Fax. +46 8 5985 2745 Switzerland: Allmendstrasse 140, CH-8027 ZURICH, Tel. +41 1 488 2741 Fax. +41 1 488 3263 Taiwan: Philips Semiconductors, 6F, No. 96, Chien Kuo N. Rd., Sec. 1, TAIPEI, Taiwan Tel. +886 2 2134 2886, Fax. +886 2 2134 2874 Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd., 209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260, Tel. +66 2 745 4090, Fax. +66 2 398 0793 Turkey: Yukari Dudullu, Org. San. Blg., 2.Cad. Nr. 28 81260 Umraniye, ISTANBUL, Tel. +90 216 522 1500, Fax. +90 216 522 1813 Ukraine: PHILIPS UKRAINE, 4 Patrice Lumumba str., Building B, Floor 7, 252042 KIEV, Tel. +380 44 264 2776, Fax. +380 44 268 0461 United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes, MIDDLESEX UB3 5BX, Tel. +44 208 730 5000, Fax. +44 208 754 8421 United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409, Tel. +1 800 234 7381, Fax. +1 800 943 0087 Uruguay: see South America Vietnam: see Singapore Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD, Tel. +381 11 62 5344, Fax.+381 11 63 5777
For all other countries apply to: Philips Semiconductors, International Marketing & Sales Communications, Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. +31 40 27 24825 (c) Philips Electronics N.V. 1999
Internet: http://www.semiconductors.philips.com
SCA 68
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights.
Printed in The Netherlands
545002/03/pp16
Date of release: 1999
Dec 14
Document order number:
9397 750 06653

▲Up To Search▲

Price & Availability of TDA8510

	To Download TDA8510 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .